Do you know you can also make a battle hammer with just a few steel rods and the instruments you have already got in your shed? Be taught with us on this information on methods to make a low-budget however useful battle hammer.
Making a Battle Hammer in Six Easy Steps
Issues You’ll Want:
- A flat metal bar (1½ x ¼ x 36) inch
- Zinc plated flat metal bar with holes (1 3/8 x 1/16 x 36) inch
- An angle iron (1 ¼ x 1/8 x 36) inch
- 14 units of three/8-inch nuts, bolts washers, and lock washers
- 1/4 -inch wooden or board
Instruments You’ll Want:
- A 3/8-inch drill bit
- An angle grinder with a grinding wheel and a cut-off wheel and
- A drill
- C Clamp
Step 1. Mark Out the Metal Bars
Firstly, use a sharpie to attract massive strains at each 5 inches on the skin of the angle iron. The road ought to cowl each side of the angle iron. Right here it is best to have 4 five-inch sections.
Subsequent, measure two inches in from the nook after which drop a diagonal line. Do that on each side of the primary two five-inch sections.
On the third five-inch part, measure two inches from the nook and solely drop a diagonal on one aspect. Do the identical on the final five-inch staff however on the alternating aspect.
Secondly, mark out a 2 ½ inches part on the flat bar. Subsequent, measure out one other four-inch and mark it out. Subsequent, from the border of the 2 areas, measure two inches into the four-inch part and drop a diagonal.
Step 2. Reduce the Marked-Out Bars
Now, use an angle grinder with a cut-off wheel to chop the angle iron and the flat bar to dimension. It can save you the items of metal you’ll not use for one more mission.
Subsequent, use the identical angle grinder to chop off the top of the zinc-plated metal bar with a half gap to match the opposite straight finish. Now, use your sharpie to mark 4 sections on the zinc-plated bar.
The primary three ought to have seven holes every, whereas the final one ought to have 13 holes. Use the grinder to chop the zinc-plated bar to dimension.
Tip: If you’re not utilizing a bar with holes, measure out 5 ¼ inches for 3 small sections and 9 ¾ inches for the extra in depth part.
Step 3. Bend the Zinc Plated Items to Kind Brackets
Right here, take a bit of your ¼ -inch flat bar, align it with the middle gap on one in all your zinc plated flat punch. Subsequent, clamp it onto your vise and bend the higher a part of your zinc plated bar over the flat bar as tightly as you’ll be able to.
You should utilize a blacksmith’s or common hammer for this. For this step, use two of the three smaller items of the zinc-plated bar.
Do the identical for the remaining zinc-plated punch items. The one distinction right here is that you’re going to bend them over two stacked flat bars. For this, use a tape measure to mark out a 22 ½ -inch after which lower it utilizing a grinder.
Notice: Stack your 22 ½ -inch flat bar with every other bar for the second layer of brackets. It doesn’t need to be the identical size.
Step 4. Bracket the Hammerhead Elements
Firstly, take two angle iron items with totally different edges (one with two diagonal strains and one other with one diagonal line. Align them on a flat floor such that the straight edges match.
Subsequent, take one of many small brackets and slide it onto the aligned iron items. Do that from the straight edge and slide it as far down as it may possibly go.
Now, tightly clamp the other edge on the vise after which use a C clamp to carry the bracket in place as you utilize a hammer to slip the bracket additional down. There ought to be no house left between the bracket and the angle bars. Repeat this step for the remaining set of angle iron rods and one of many smaller brackets.
As soon as completed, clamp the bracketed angle iron bars with a C clamp to maintain every thing in place. Subsequent, clip the iron bars onto the vise. Afterward, take away the C clamp and use a drill to make holes on the bracketed angle bars.
That is easy as you’ll solely have to undergo a gap on one aspect of the bracket and drill till you come out by means of the bracket gap on the other aspect. As soon as completed, insert a bolt, washer, lock washer, and tighten the nut with a ratchet.
Subsequent, flip the hammerhead half and do the identical for the third punch gap. After drilling a gap and tightening the nut, it is best to have one undrilled gap within the center. Repeat this with the opposite bracketed set of angle iron bars.
Step 5. Assemble the Hammerhead
Now align the 2 units of bracketed angle iron bars such that they’re symmetrical with one another. This manner, you’ll find yourself with one straight edge with no diagonal lower on the aspect of the hammerhead.
To this edge, slide on the big zinc-plated bracket. Subsequent, slide the remaining small bracket on the opposite fringe of the hammerhead. Slide it from the straight finish. Remember the fact that these two brackets may have loose-fitting.
Subsequent, flip the hammerhead and suit your 2 ½ -inch spacer between the 2 angled items of the hammerhead. You should utilize one other steel to push the spacer to position. As soon as the spacer is in place, the 2 brackets will now match snugly.
Now drill extra holes onto the 2 new brackets and tighten your bolts. Be certain that your two new bolts don’t intervene along with your beforehand added bolts.
Step 6. Connect the Metallic Deal with and the Punching Spike
As soon as the hammerhead is assembled, slide the 22 ½ – inch flat rod by means of the house between the 2 angled elements of the pinnacle. Be certain that it’s firmly pressed towards the primary spacer you inserted. When in place, drill two extra holes and insert the bolts to carry them in place.
Subsequent, slide the armor punching spike onto the again of the hammerhead and drill in two holes for the 2 bolts that may maintain it in place. Lastly, screw on the deal with and wrap it with a paracord for comfy dealing with.
Notice: If you happen to resolve to color your battle hammer, take the hammerhead aside, paint every thing besides the brackets and bolts, after which reassemble it.
Watch this video by ZNA Productions on methods to make: the battle hammer:
There you’ve it, preppers. With this easy illustration, you make simply make a battle hammer at dwelling. What’s extra, it doesn’t require a lot, and subsequently you’ll not need to lay our a fortune to personal one. Get artistic and customise yours to your wants and style.
The place will you utilize your battle hammer? Tell us within the remark part beneath!
Calling all preppers, craftsmen, bushmasters, outdoorsmen, and all-around expert folks, Survival Life wants YOU! Click here if you wish to write for us.